Showing results: 46 - 60 of 277 items found.
-
2575A -
Valhalla Scientific Inc.
A versatile, powerful calibration tool, the 2575A Precision AC-DC Active Current Shunt measures both AC/DC current and works as a standard for low-level resistance calibration requirements.
-
SGT-200 -
Manta Test Systems
The Vanguard SGT-200 Safety Ground Tester is a 200A DC micro-ohmmeter designed specifically to measure the resistance of protective in-service grounding and jumper cable assemblies. The SGT-200 can measure the resistance of the grounding cables, clamps and ferrules. The measured resistance values can be compared against the calculated values (using the ASTM 2249-03 standard) and a Pass/Fail result can be printed along with the measured resistance values. Since the SGT-200 uses a DC current, there is no need to uncoil the cable under test. It can be conveniently tested in its coiled state in a much smaller testing enviornment.
-
Sanwa Electric Instrument Co., Ltd
Test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
Guangzhou Hanker Electronics Technology Co., Ltd
Is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
AOIP
Industrial platinum resistance thermometers 935 are suitable for use in the laboratory or on site. They can be used as a standard work on an oven or a calibration bath or as a precision sensor for our temperature indicators thermometers.
-
DMM -
Greenlee Tools
Is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
ASTM D257 -
National Technical Systems
These test methods cover direct-current procedures for the measurement of dc insulation resistance,volume resistance, and surface resistance. From such measurements and the geometric dimensions of specimen and electrodes, both volume and surface resistivity of electrical insulating materials can be calculated, as well as the corresponding conductances and conductivities. These test methods are not suitable for use in measuring the electrical resistance/conductance of moderately conductive materials. Use Test Method D4496 to evaluate such materials. This standard describes several general alternative methodologies for measuring resistance (or conductance). Specific materials can be tested most appropriately by using standard ASTM test methods applicable to the specific material that define both voltage stress limits and finite electrification times as well as specimen configuration and electrode geometry. These individual specific test methodologies would be better able to define the precision and bias for the determination.
-
Dongguan Amade Instruments Technology Co., Ltd
Footwear testing machines are designed to determine a variety of mechanical and chemical performances of different types of shoe materials and finished shoes including sneakers, high-heeled shoes, leather shoes, casual shoes, etc. There are appearance performance tests including yellow resistance test, ageing resistance test, fastness resistance test, etc, physical performance tests containing flexing resistance test, rubbing resistance test, anti-slip test, etc, biological and chemical performance tests covering PH test, Formaldehyde content test, flame retardant test, etc, and service life test. Applicable to standards of ISO20344, SATRA, ASTM, etc.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Short Circuit Test Machine Relevant standards requirement:Single Storage Cell Safety Test6.2.4 Short circuitCharge the single storage cellaccording to 6.1.3 standardThe cellis to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩ for 10 minObserve for 1HBattery module safety test6.3.4 Short circuitCharge the battery module according to standard 6.1.4The battery module is to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩfor 10 minObserve for 1H
-
M200 -
CAPRES A/S
The window of acceptable sheet resistance is shrinking with each technology node resulting in increasingly more rigorous standards for scale and accuracy of metrology tools. The shortcomings of traditional types of 4 point probes are becoming more and more evident. By developing the microRSP-M200, a unique tool for measuring the sheet resistance of conducting films, hereunder ultra shallow junctions (USJ’s), CAPRES A/S has responded to the growing need for reliable sheet resistance measurements on micro scale.
-
PU 296 -
Metra Blansko a.s.
The instrument PU 296 is intended for measurements of voltages, insulation resistances and determination of coefficients PI, DD and DAR at revisions of the high-current equipment. It complies with requirements of the standard ČSN EN 61557-2.
-
PMK-153 -
Prostat Corporation
The PMK-153 Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-153 includes the PAS-853B Wide Range Ohmmeter with 5 pound Conductive Rubber Electrodes. The PAS-853B instrument is a wide range ohmmeter that measures accurately from 0.01 to 9.9x1012 ohms. In AUTO mode the instrument automatically adjusts resistance range and selects test voltage in accordance with standard practices outlined in ANSI/ESD STM11.11, and meets audit requirements of ESD TR53.
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
Milwaukee Electric Tool Corporation
A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
CTS Valpey Corp.
When a design calls for a variable resistance, CTS can supply a solution in the form of a wide variety of rotary and slide-action variable resistors / potentiometers. Our rotary potentiometers are available in various sizes ranging from 9mm square to 24mm in diameter, while slide-action potentiometers are available with travel from 10 to 60 mm. CTS rotary potentiometers can be constructed using conductive plastic, traditional carbon, or wire-wound elements. Our conductive-plastic potentiometers feature a standard 2% linearity and 2 million life cycles with a standard resistance tolerance of 10%. Our conductive-plastic rotary potentiometers handle as much as 0.25 W power in operating temperatures of -40 to +125C. CTS wire-wound rotary potentiometers offer standard linearity of 3% with 2% available upon request, and a resistance tolerance down to 5%. Our wire-wound rotary potentiometers come with a 5 Watt power rating in operating temperatures of -30 to +105C. Standard wire-wound rotary potentiometers are designed for 10,000 life cycles, although models built for 50,000 and 100,000 cycles are available upon request. For those in need of slide-action potentiometers, we offer a range of carbon composition pots with standard features such as 10,000 life cycles, linear and audio resistance tapers, and available with tolerance of 10%.
